Designed for High Performance
Clarification and Particle Removal
Profile II cartridges are high efficiency depth style filters constructed of polypropylene. Constructed of polypropylene, with a continuously graded fixed pore structure, these cartridges provide pre- and final filtration within the same cartridge resulting in lower overall filtration and disposal cost.
The Profile II filter cartridges provide a removal efficiency of >99.98% in compatible liquids with consistent filtration performance.
|
| Fixed fiber matrix |
- Consistent filtrate quality
- Highly stable structure
- Process reliability
|
| Continuous pore size variation from coarse to fine |
- High dirt holding capacity
- Longer service life
|
| Available in multiple configurations |
Easy to integrate into existing lines |
| Polypropylene construction with no adhesives or surfactants |
Broad chemical compatibility |
|
Food Contact Compliance
Materials of Construction
|
| Media |
Polypropylene |
| Core |
Polypropylene |
| Cage, End Cap and Fin End |
Polypropylene |
| Adaptor |
Polypropylene with a stainless steel reinforcing ring |
| O-ring Seal |
Ethylene propylene rubber or silicone elastomer |
| Elastomeric End Cap and Seal |
Thermoplastic elastomer |
|
Operating Characteristics in Compatible Fluids1
|
| 4 bard (60 psid) |
30 °C (86 °F) |
| 3 bard (50 psid) |
50 °C (122 °F) |
| 2 bard (30 psid) |
70 °C (158 °F) |
| 1 bard (15 psid) |
82 °C (180 °F) |
| 0.3 bard (5 psid)2 |
125 °C (257 °F) |
|
Sterilization and Sanitization3
|
| in situ Steam Sterilization |
125 °C (257 °F) |
10 hours |
| in situ Hot Water Sanitization |
80 °C (176 °F) |
|
|
Typical Flow Rates4
It is recommended that the Max. Flow rate be selected such that the clean element pressure drop does not exceed 0.7 bar (10 psid) for optimal assembly life. Please contact Pall for optimized sizing.
1Compatible fluids are defined as those which do not swell, soften or attack any of the filter components.
2AB style only
3For applications requiring Sterilization or Sanitization Pall recommends the use of the Code 7 adapters to ensure filter sealing after cooling. Cartridges should be cooled to system operating temperature prior to use.
4Typical initial clean media ØP 254 mm (10") element, water at 20 °C (122 °F), viscosity 1 cP. For assistance with filter assembly, sizing and housing selection, contact your local Pall representative.
Quality
- Cartridges produced in a controlled environment
- Manufactured according to ISO 9001:2008 certified Quality Management System
This information is a guide to the part number structure and possible options. For availability of specific options and housing details, please contact Pall.
Example Part Number: AB
2 Y
010 3 W
J (See bold references in tables below.)
Element Part Number: AB < LENGTH Code from Table 1> Y <REMOVAL RATING Code from Table 2 > < ADAPTOR Code from Table 3> W < O-RING SEAL code from Table 4>
Table 1 - Nominal Length
|
| 1 |
254 mm (10 in.) |
| 2 |
508 mm (20 in.) |
| 3 |
762 mm (30 in.) |
| 4 |
1016 mm (40 in.) |
| 01 |
25.4 mm (1 in.) |
| 05 |
127 mm (5 in.) |
| 09 |
228.6 mm (9 in.) |
| 39 |
990.6 mm (39 in.) |
| 29 |
736.6 mm (29 in.) |
|
Table 2 - Liquid Removal Rating
|
| 005 |
0.5* |
<0.5* |
| 010 |
1.0 |
<0.5* |
| 030 |
3.0 |
<1.0* |
| 050 |
5.0 |
2.0 |
| 100 |
10.0 |
6.5 |
|
*Extrapolated value
Profile II filter cartridge liquid retention ratings are based on ANSI B93.31.73 modified for single pass testing in an aqueous medium.
Table 3 - Adaptor
|
| 3 |
SOE - single open end with flat closed end and external 222 O-rings |
| 7 |
SOE - single open end with fin end, 2 locking tabs and external 226 O-rings |
| 8 |
SOE - single open end with fin end and external 222 O-rings |
| 28 |
SOE - single open end with fin end, 3 locking tabs and external 222 O-rings |
|
Code 3, 7, 8 and 28 may be available in selected grades, confirm code availability with your Pall representative
Table 4 - O-ring Seal
|
| H4 |
Silicone Elastomer |
| J |
Ethylene Propylene Rubber |
|
Print Product Information
E-Mail
Download PDF
